Electronic Vehicle Information Center (EVIC) Displays
The EVIC display consists of three sections:
1. The top line where compass direction, odometer line and outside temperature are displayed.
2. The main display area where the menus and pop up messages are displayed.
3. The reconfigurable telltales section below the odometer line.
The main display area will normally display the main menu or the screens of a selected feature of the main menu. The main display area also displays pop up messages that consist of approximately 60 possible warning or information messages. These pop up messages fall into several categories:
• Five Second Stored Messages
When the appropriate conditions occur, this type of message takes control of the main display area for five seconds and then returns to the previous screen. Most of the messages of this type are then stored (as long as the condition that activated it remains active) and can be reviewed from the Messages main menu item. As long as there is a stored message, an i will be displayed in the EVIC’s compass/outside temp line. Examples of this message type are Right Front Turn Signal Lamp Out and Low Tire Pressure .
• Unstored Messages
This message type is displayed indefinitely or until the condition that activated the message is cleared. Examples of this message type are Turn Signal On (if a turn signal is left on) and Lights On (if driver leaves the vehicle).
• Unstored Messages Until RUN
These messages deal primarily with the Remote Start feature. This message type is displayed until the ignition is in the RUN state. Examples of this message type are Remote Start Aborted - Door Ajar and Press Brake Pedal and Push Button to Start .
• Five Second Unstored Messages
When the appropriate conditions occur, this type of message takes control of the main display area for five seconds and then returns to the previous screen. Examples of this message type are Memory System Unavailable - Not in Park and Automatic High Beams On .
The Reconfigurable Telltales section is divided into the white telltales area on the right, amber telltales in the middle, and red telltales on the left.
When the appropriate conditions exist, the EVIC displays
the following messages:
• Key in ignition
• Ignition or Accessory On
• Remote start aborted — Door ajar
• Remote start aborted — Hood ajar
• Remote start aborted — L/Gate ajar
• Remote start aborted — Fuel low
• Remote start disabled — Start Vehicle to Reset
• Remote start active — Push Start Button
• Remote start active — Key to Run
• Wrong Key
• Damaged Key
• Key not programmed
• Vehicle Not in Park
• Key Left Vehicle
• Key Not Detected
• Press Brake Pedal and Push Button to Start
• Door(s) Ajar (with a single chime, if vehicle is in motion)
• Liftgate Ajar (chime will sound when vehicle starts moving)
• Low Tire Pressure
• Service TPM System (refer to “Tire Pressure Monitoring System” in “Starting
And Operating”)
• Turn Signal On
• RKE Battery Low
• Service Keyless System
• LOW WASHER FLUID
• Oil Change Required
• Check Gascap
• Left Front Turn Signal Light Out
• Left Rear Turn Signal Light Out
• Right Front Turn Signal Light Out
• Right Rear Turn Signal Light Out
• Park Assist Disabled
• Service Park Assist System
• Personal Settings Not Available — Vehicle Not in Park
• Blind Spot System Off — This message is displayed
when the ignition is turned to ON to indicate the Blind
Spot System has been turned off.
• Blind Spot System Not Available — This message is
displayed to indicate the Blind Spot Monitor (BSM)
system is temporarily unavailable due to sensor blockage,
electronic interference, or other temporary conditions.
When this message is displayed both outside
rear view icons will be illuminated. If electronic interference
is present, the BSM system will illuminate the
icon only on the side of interference as long as
interference is present.
• Service Blind Spot System — This message is displayed
to indicate the Blind Spot Monitor (BSM)
system is permanently unavailable. The driver will
receive an EVIC message and the BSM display warning
in both mirrors will be permanently illuminated. If
this message is present see an authorized dealer.
See also:
Operation
Voice commands can be used to operate the Uconnect™
Phone and to navigate through the Uconnect™ Phone
menu structure. Voice commands are required after most
Uconnect™ Phone prompts. You wi ...
Power Lumbar — If Equipped
Vehicles equipped with power driver or passenger seats
may be also be equipped with power lumbar. The power
lumbar switch is located on the outboard side of the
power seat. Push the switch forwa ...
Tire Markings
1 — U.S. DOT Safety Standards Code (TIN)
2 — Size Designation
3 — Service Description
4 — Maximum Load
5 — Maximum Pressure
6 — Treadwear, Traction and Temperature Grades
NOTE:
...